Replacement of light-tight foam around back cover, at hinge area and inside mirror box (mirror bumpers). Every OM, XA, RF body I see has BAD mirror and back foam. BAD FOAM IS ALWAYS REPLACED. Bad prism foam is removed (OM-1 thru 2N) and not replaced. Even 3Ti's, 4T's and Ti's get new back & mirror foam. This is replaced as a regular part of every overhaul. There is no discount if you've done your own foam replacement and ask me not to do it. Badly botched foam installations may be left as-is, especially if glued in with the wrong glue (like silicon).

The OM-1/1N  overhaul price includes conversion to the silver oxide 1.55v battery. New battery is extra.  Use 357, SR44, MS76, KS76, G13, S76 or silver oxide equivalent. If you are using an MR9 and don't want the internal conversion, be sure to mention it in your cover letter. My internal silver oxide conversion essentially builds the diode of the MR9 INTO the meter circuit: no adapter to buy or lose. 

Body is cleaned af dust, debris, lint. Gears and levers are cleaned and re-greased, small worn out parts (if any) are replaced. There may be a lot of work done during an overhaul that is not listed here.


In multiple OM body repairs, I do my best to match cameras to one another. When finished they will be very close to each other (usually 1/8th to 1/16th of a stop). Overhauled bodies may not match meters in camera's which you have not had overhauled yet.

Meters are generally adjusted to "zero". Meters will not necessarily match exactly at all light levels (this cannot be done). This applies to OM bodies. Older RF repairs (35RD, RC, ED, SP, SPn, etc.) are discontinued from my service line.  Meters calibrated by Camtech will not necessarily match other camera's or handheld meters you may have that have not been overhauled.

Completed, paid overhauls are covered by a 3 month warranty (90 days). Warranty is void if equipment is abused (dropped, tampered, exposed to sand, water etc.) Warranty is also voided if someone else tries to fix it (as in "well, it seemed like a simple problem and I didn't want to have to send it back. My uncle said he could fix it") BOIOIOING....warranty cancelled. No warranty on aftermarket leather coverings, though we are very careful with them. Leather covers are "self stick" and may peel up and with age and handling.  Also, leather coverings may stain.

This description of ' what an overhaul is ' applies to your item when sent for repair. WE DO COMPLETE OVERHAULS ONLY!  NO PARTIAL REPAIRS HERE.  That is in your best interests. What is itemized below applies to most OM bodies & lenses, XA's, and Pen SLR bodies and lenses. 

  


Each repair is done one at a time, from beginning to end, and is usually shipped by Priority Mail the same day the work is completed. After the estimate is approved, (and it's your turn in line) your repair gets our undivided attention (approximate turnaround time is on our index page.)

First, your main complaints are addressed (whatever they might be). Wind jammed, release jammed, no flash sync, meter not working? (....there could be 6 different things that could cause a meter to fail.) If a dead meter can be fixed without replacing the meter coil itself, then it will probably be fixed under the flat rate overhaul price. If required, parts and prices will be listed separately.

Adjustment of curtain speeds and shutter shutter speeds to factory specs (curtains must go across the film aperture at the same speed). High shutter speeds are NEVER adjusted by tweaking the curtain speeds. That would make 1/1000 accurate ONLY in the center of the frame.

Adjustment of meter position to factory specs (meter accuracy and actual exposure are 2 independent systems. Meter needle position can be off plus or minus while actual speed or auto exposure is on the button etc.) Sorry, no meter warranty if used with wrong, non-linear, poor performance batteries (weincell, A76, LR44, CR1/3N).